— Build Your Own Kit —
Boat Trailer Landing Strip LED Light Kit

Add landing strip LEDs to your boat trailer for better visibility. Can be configured for trailers up to 40' long (perhaps a little longer). Will accomodate multiple bunk configurations.

This Boogey Lights® BOAT TRAILER LANDING STRIP LED light kit is designed to mount to the boat trailer support struts with the LED strips facing upward; typically mounted close to and parallel to the trailer bunks. When illuminated, the light coming from these LED strips make it easier to see the bunks when the trailer is submerged. The optional aluminum channels with diffusers provide a more polished, professional look while also providing an additional layer of protection for the LEDs. The diffuser gives off a nice glow lighting effect too; similar to a light stick.

We also offer the UNDER-GLOW LED LIGHT KIT which appears in some of the product photos shown on this product page. That kit is sold separately. The Landing Strip light kit and Under-Glow light kit can be used together or individually.

Offered in three MULTI-COLOR versions (RGB, RGBW and RGBA), seven different DUAL COLOR versions and eight different SINGLE COLOR versions. The default configuration is set at RGB because it is the most popular but you can adjust the LED color selection using the drop down product options on this page for the other color options.

We encourage you to take time to review the information we have assembled here before making your purchase decision. Be sure to scroll down, expand each text group section and read the information presented within each group. It's very thorough. Be sure to click on the INSTALL tab too. This is where you'll find downloadable INSTALL DOCUMENTATION and WIRING DIAGRAMS for this kit. These materials contain important installation considerations.

The Boogey Lights® LOW PROFILE LED strips used in this light kit are sealed against the elements. They're IP65 rated. They are heat resistant, waterproof and easily cleaned for maintenance free operation. Note that these LED strips are NOT intended for use in salt-water applications. If you use them in salt-water, you need to clean them after each use. If not, the salt will dry and will eventually erode the epoxy coating allowing water to intrude and corrode the lighting circuit. We do not warranty this product if used in salt water for this reason. These lights are intended to be used with fresh water applications where the boat is submerged for short periods of time (e.g. launching and loading a boat on a boat ramp). They are not designed to be used for extended periods of time submerged under water. These are not marine grade LED lights which fall into another lighting classification. See below video of an example of these lights are typically used on a boat trailer.

NOTE: We do not include a trailer wiring harness with this kit. Why? Because there are too many variations and configurations possible. Plus, you can purchase a 4 way flat, 5 way or even 7 way trailer plug/harness at any auto parts store or online. They're inexpensive and plentiful.

Some of the photos shown in this product page include both our BOAT TRAILER LANDING STRIP LIGHTS and our UNDER-GLOW LED LIGHT KIT. The Under-Glow Light Kit is sold seperately. Product photos and installation of Boogey Lights® done by CTS CUSTOM TRAILERS. Check them out!

VIDEO

This video shows our RGB multi-color boat trailer landing strip LED light kit mounted on a triple axel boat trailer. It's operated using our GEN2 LED controller mounted in the tow vehicle. It can be operated using the included RF wireless hand held remote or using our free Bluetooth APP and your smartphone. Video and installation of Boogey Lights® done by CTS CUSTOM TRAILERS.

This video shows our boat trailer landing strip LED light kit in action. Video and installation of Boogey Lights® done by CTS CUSTOM TRAILERS.

PRODUCT FITMENT

This product can be configured to fit just about any boat trailer up to 40' (perhaps longer) in length. The kit allows for a total of six LED segments (see layout diagram); three on each side of the trailer (although you can mount them anyway you'd like). You'll need to measure the mounting surface you have available and then based on those measurements, order the length of LED strips needed to cover that area. For shorter trailers and/or trailers with only two bunks, you'll likely only need two LED strips (one on each side of the bunks). For longer trailers or trailers that have more than two bunks, you'll likely need more LED strips to achieve the desired lighting effect. Note that you don't have to use all six LED segments nor do you have to mount them on each side like we show on the layout diagram. You could for example mount a single LED strip down the center of the trailer if that fits your boat configuration better. The point is that the length, number of, how and where you mount these LED strips is totally up to you. The LED strips don't care where you mount them as long as you make sure they're mounted in such a way that the strips can not come in contact with the boat. Be sure too to mount them to a straight, flat, rigid, flat surface. Details of the mounting restrictions can be found in the install docs provided on this product page. We suggest reviewing them before purchasing. In some cases you may need to build out the mounting surface using aluminum, wood or similar structure. It all depends on the construction of your trailer and where you are mounting the LED strips. Note too that the optional aluminum channels with plastic diffusers offered on this kit are NOT intended to be used as a structural mounting surface. They're too light and will flex too much if not supported properly. Scroll down further on this product page for more details about the aluminnum channels offered.

The maximum length of a single LED strip is 16'. They cannot be built longer (details as to why can be found further down on this product page). For longer distances, use multiple lengths which is one of the rasons why this kit offers up to six LED strips total. If you need more than six LED strips for your trailer, you can purchase additional LOW PROFILE strips here. Each LED strip comes with a 15' power lead permanently attached to one end of the LED strip. The other end is bare; no connector. It is intended to be hard wired into the wiring harness. We include additional feeder cable with the kit for use in connecting the LED strips and running the wiring harness up to the tongue of the trailer.

For those who want a more professional, polished look, we offer the option of ordering aluminimum channel with plastic diffusers. The aluminum channel is typically secured to the trailer using rivets or screws and then the LED strip is mounted inside the aluminum channel with the plastic diffuser going on top. We then seal the ends with Lexel (or equiv).

For multi-color RGB/RGBx configurations, you'll need an LED Controller. The LED controller is intended to be mounted in the tow vehicle. It should not be mounted on the trailer itself unless the mounting location is protected from the elements; mainly water. The LED controller cannot be submerged.

Taking Measurements | What You Need to Know

It's important when measuring your trailer to examine the mounting area you have available. When doing so, make sure the area where you will be attaching the LED strip is clean, straight, smooth and rigid. The LED strip MUST be mounted flat against a single continuous, rigid mounting surface, in a straight line; it cannot bend around a radius or corners. Plus, the entire strip needs to be stuck to the mounting surface and not span across mounting surfaces. If you do, the strip will almost certainly fail in the spot that isn't affixed firmly to the mounting surface or, the point at which is spans across the two mounting surfaces. If you don't have a smooth, flat, rigid, contiguous mounting surface we recommend riveting or screwing aluminum, plastic L channel or similar to the trailer's cross member support beams and then mount the LED strip to that surface. The point is to carefully examine the mounting locations for your trailer when you're taking these measurements before placing your order.

Once you have identified the mounting locations and have your measurements, you're ready to place your order using this product page. You'll notice each LED strip segment on this product page has a drop down box listing the 16 available lengths for every LOW PROFILE LED STRIP. There are six possible LED strips in this kit. For those LED segments that don't apply to your trailer, simply leave them set to 'none'. For each LED segment, select the corresponding LED length from the drop down.

PRODUCT OPTIONS

Some are required. Some are optional. Refer to the following for details on each of the product options offered.

LED COLOR OPTIONS: This option tells us what color format you want for your light kit. There are three multi-color, seven dual color options and eight single color options. We have a detailed discussion about these LED color options further down on this product page. Be sure to read it. It's important. If you select any of the three multi-color options, you'll be presented with the option to make an LED CONTROLLER selection (essential to operate RGBx LEDs). If you select any of the dual color or single color options, you'll be presented with a switching option.

CONTROLLER CONFIGURATION: The controller configuration will vary based on your LED color selection. More information about these options are further down on this product page. Be sure to review them.

LED STRIP LENGTHS: There are six possible LED strip lengths you can order on this kit. You only have to order one LED strip. The other five are optional. Each LED STRIP is numbered 1 through 6. These numbers correspond to the layout diagram we include in the photo gallery of the product page as well as shown below (scroll down). Using the drop down box select the length of the LED strip you want for each LED strip. For any unused LED lengths, leave set to 'NONE'. Minimum length is one foot. Maximum length is 16 feet.

ADD ALUMINUM CHANNEL W/DIFFUSER: This product selection is optional but if you can afford it, we suggest adding it. Why? Because they provide a professional looking installation. Not only does the channel and diffuser protect the LED strip the opaque plastic diffuser gives off a nice glow lighting effect too. Scroll down for more information (and photos) about this option.

MULTI COLOR CONTROL OPTIONS

RGB, RGBA or RGBW MULTI-COLOR OPTION: The multi-color RGB LED version provides over 16 million color combinations that you control and includes its own on/off wireless switch. The multi-color RGB, RGBA and RGBW kits include our GEN2 Heavy Duty combo Bluetooth + RF controller so you can control the lights with your Bluetooth enabled smartphone or the included wireless RF G2 M7 remote control. The CONTROLLERS navigation tab on this product page has additional details. With any of the Boogey Lights® BLUETOOTH controllers you can control your lights with your Bluetooth enabled Android or IOS smartphone. These high-tech controllers are capable of displaying 16 million different color combinations. In addition, lighting effects on the Smartphone controller are significantly more controllable in terms of speed and intensity. Each color and lighting effect is controlled by "sliders" or a color square on your smartphone screen so you can adjust the speed and intensity to get the lighting exactly the way you want it. Our controllers operate on 12vdc. Also, all of our Bluetooth Combo controllers include an RF remote control allowing for quick on/off of the controller. You can operate this controller with the included RF wireless remote OR you can use your Bluetooth enabled smartphone and our free smartphone APP (Android and IOS). Boogey Lights® RF Controllers will display seven colors (steady on + four lighting effects): RED, GREEN, BLUE, WHITE, LIGHT BLUE, BOOGEY LIGHTS GREEN (LIME GREEN/YELLOW), HOT PINK/PURPLE. The lighting effects options for our RF Controller include: DIMMING, BLENDING, BREATHING, STROBING. In the Blending, Breathing and Strobing modes these features can be set to remain on a single color or to cycle through each of the 7 colors. You can also adjust the speed at which this happens. The RF remote control offers SEVEN levels lighting effects (e.g. 7 levels of dimming). For the DUAL ZONE Heavy Duty LED controller, these functions work independently per zone OR both zones together.

Quick Switch: The Quick Switch feature comes standard on our HEAVY DUTY SINGLE ZONE and HD DUAL ZONE LED Controllers (all RGBx controllers). Whatever color LED you have connected to the WHITE output wire on the controller is the color that will display when the Quick Switch is triggered with 12vdc +. The most common use for this configuration is with commercial vehicles who want to be able to instantly turn off whatever color they're running and turn on a DOT compliant AMBER which is on our RGBA LED strips. For these installations, the yellow trigger wire is connected to a toggle switch or other wireless switch that activates the AMBER leds. When the Quick Switch trigger wire is not energized, the LED controller operates the RGBxx diodes normally. NOTE: This Quick Switch feature eliminates the need to use a relay for RGBA LEDs.

Single Zone or Dual Zone: If ordering RGB or RGBA, you have your choice of a SINGLE ZONE or DUAL ZONE GEN2 Heavy Duty LED Controller. As the name suggests, a SINGLE ZONE controller has one lighting zone. All LEDs wired to that zone display the same color and features. For DUAL ZONE, there are two distinct lighting zones. All LEDs wired to Zone 1 operate the same. All LEDs wired to Zone 2 operate the same. Each zone can be used independently or together.

SINGLE COLOR or DUAL COLOR CONTROL OPTIONS

If you're ordering any of the Single Color or Dual-Color LED color options, you'll be presented with the option to add our Dual Zone Controller to the order. This is an option. The default is 'none'. If selecting the Dual Zone Controller with any of the single color or dual-color options, you'll receive our Strobing Dual Zone single color controller. Designed primarily for commercial, working truck applications this heavy duty LED controller is ideal for situations where you need to control (on/off), strob or flash large numbers of single color LEDs. A typical scenario is with wide load truck haulers, wreckers and tow trucks. A typical scenario is with wide load truck haulers, wreckers and tow trucks. The unique dual zone capability allows the lights to be segregated into two distinct lighting zones if that's what you want to do.

For example zone one might be red LEDs and zone two amber LEDs. Another option could be to assign the two zones into LEDs mounted on different parts of the trailer (underglow = blue, landing strip lighting = amber). The options are endless. Each zone can be operated independently or together. In addition to ON/OFF control, STROBING and FLASHING, there's a STEADY-ON mode that offers dimming. All of these features are operated using the included wireless RF handheld remote.

Each zone will support up to 1500 tri-chip 5050 LEDs (20Amps) which means a total of 3000 tri-chip LEDs on a single LED controller. The operating modes include strobing, 3 burst flash and solid on. The speed can be adjusted and there's a brightness setting too. All of these features are operated using the included wireless RF hand held remote. This controller includes our Quick-Switch feature which when paired with a simple on/off switch will allow the controller to be turned on/off via a hard wired switch (mounted on the dash for example) as well.

The CONTROLLERS navigation tab on this product page has additional details on this controller option.

SINGLE COLOR VS MULTI-COLOR (RGB, RGBx)

Single colors are going to be brighter than RGB (multi-color) LEDs. The reason is that in an RGB LED there are three diodes: red, green and blue. The LED controller mixes those three colors to create other colors. For example, equal amounts of red + green + blue = white. In a single color LED, all three diodes are the same color. So in a single color white LED, there are three white LEDs which is much brighter than an RGB led mixed to show white. If you're looking for the absolute brightest color for your trailer, go with single color. If however you want to be able to change the colors from time to time, go with RGB. Just be aware that the RGB version of isn't as bright as the single color version. The single color version is available in your choice of one of seven super-bright colors: Amber, Orange, Red, Green, Blue, White or Pink.

RGB / Multi-Color: For RGB led lighting an LED Controller is needed to operate the lights. The controller is what operates the lights and mixes the colors. In addition to providing a wireless on/off capability, the LED controllers offered allow you to control your lights with your Bluetooth 4.0 enabled smart phone and our free smart phone APP (Android and IOS) OR the included RF wireless remote. With the included RF remote you can change between 7 colors (white, red, blue, green, light blue, lime green, pink) and functions of on/off, blending, strobing, breathing, flashing, fading and dimming. You can also use your Bluetooth enabled smart phone to create that custom look with over 16 million different color combinations plus three pre-sets along with color rotation programming with either 2 or 3 color sets. There is significantly more detail on the BLUETOOTH APP navigation tab on this product page. Since our Dual Color products use the RGB chip on the RGBA led strip, it is considered a multi-color product even though you don't need an LED controller to operate.

NOTE: If purchasing RGB, be aware that an RGB LED cannot create the color orange. It can come close but not exact. Why? As mentioned previously, RGB leds have three color DIODES: RED, GREEN and BLUE. It's the mixing of these three colors together that create other colors. The color ORANGE is created by mixing RED + YELLOW. The color YELLOW is created by mixing RED + GREEN. With an RGB LED, there is only one RED diode so it can only be used once. To get something that looks more like orange to the human eye using RGB LEDs you need to mix equal amounts of RED + GREEN (actually just a bit less green since the human eye is more sensitive to green wavelengths). This will give you the color YELLOW. Then, increase the intensity of the RED just a little (or, pull back the green). This will essentially add a little red to the yellow to effectively mix a color that has an orange tint which is closer to AMBER. It's not perfect but it's as close as you can get to the color orange using RGB led lights. If a true orange color is important to you, purchase the RGBA LEDs instead. Mixing Red and Amber produces a vibrant orange.

SINGLE ZONE OR DUAL ZONE?

For the three multi-color LED options, this kit offers both SINGLE ZONE and DUAL ZONE controller options. As the names suggest, a Single Zone controller has just one single lighting zone. All LEDs wired to the controller are on one zone. Whatever color or feature set you apply will be what you get on all leds. Pretty simple. With our Dual Zone controller, you can set up and operate two distinct lighting zones which can be operated and controlled individually or together. On a Dual Zone controller each lighting zone is capable of supporting up to 1500 LEDs for a total of 3000 LEDs. It will work with your Android® or iOS® Smart phone. It will also work with the included M7 Style RF wireless remote. Details on features are below.

GEN2 LED CONTROLLERS

Bluetooth + RF Combo Wireless Control

The LED Controllers offered in this kit are our GEN2 Single Zone and Dual Zone Heavy Duty Bluetooth COMBO LED Controllers. COMBO means they can be operated using either the included M7 RF wireless hand held remote OR your Bluetooth enable smart phone (and our free APP). Both will work. The RGB version is capable of displaying 16 million different color combinations. The GEN2 RGBx version can display even more color combinations depending on the type of LED strips connected to them. In addition, lighting effects on the Bluetooth controller are significantly more controllable in terms of speed and intensity. Each color and lighting effect is controlled by "sliders" or a color square on your smart phone screen so you can adjust the speed and intensity to get the lighting the way you want it.

Key Features & Capabilities

Our GEN2 LED Controllers are based on the Bluetooth 5 chip set family which provide fast response times and the best possible RF/Bluetooth transmission distance.
The SUPER and HEAVY DUTY GEN2 Controller can support Single Color, RGB, RGBx and RGBxx LED strips with both RF and Bluetooth control.
The HEAVY DUTY controller versions include two antennas: a screw-on 2" stubby antenna and an extended magnetic mount antenna with 15' of wire for optimal reception on any vehicle.
Use the included RF wireless remote to quickly turn on/off/dim your Boogey Lights. You can also select up to 7 different preset colors using the RF remote as well as access 7 different lighting features.
Use your smart phone to operate your Boogey Lights®: On, Off, Dimming, Color Selection, Brightness, Speed, Color Programming, Timers
Adjust the color sliders or color square to select the color you want.
Access additional lighting features (e.g. strobing, flashing, breathing, morphing) modes using the 7 Function Keys.
Save your favorite lighting configuration using Pre-Sets
Countdown Timer and a 24 hour On/Off Timer function
Quick-Switch feature for use with RGBx LED strips.
Password protection to stop others from connecting to your LED controller.
Programmable Color Rotation mode offers the ability to program the controller to display two or three colors of your choice and then rotate those colors in sequence.
Assign a 'nick name' to your controller so you can easily find it when scanning.
Set the APP to auto-connect to your LED controller every time you launch the APP on your phone
DOWNLOAD the GEN2 LED Controller Operating Manual & Wiring Diagrams
DOWNLOAD the GEN2 Bluetooth Operating Manual
DOWNLOAD the GEN2 M7 RF Wireless Remote Operating Information
VIEW the GEN2 LED Controller Series Product Page
VIEW the GEN2 BLUETOOTH APP Information Page

Color Options and Considerations

This light kit is offered in eight single color options, seven dual color options and in three multi-color configurations: RGB, RGBW (RGB + warm white) and RGBA (RGB + amber).

For the single color and dual color options you can select a simple on/off switch or a wireless controller.

For the multi-color RGB options, you have the same capabilities as the single color however the feature set is significantly expanded since you also have the ability to change/adjust/tweak the colors you want to display. RGB stands for Red Green Blue. It's the mixing of these three primary colors together that will produce up to 16 million different color options. To mix and produce these colors however you need an LED controller which is why when you select any of the RGB or RGBx color options you'll also be prompted to make a LED Controller selection. The Boogey Lights® LED controllers offered are both RF wireless + Bluetooth enabled controllers. With the included RF wireless remote you can change between 7 pre-set colors (Red, Green, Blue, White 6000K, Light Blue, Lime Green/Yellow, Hot Pink/Purple) and functions of on/off, blending, strobing, breathing, flashing, fading and dimming. You can also use your Bluetooth enabled smart phone to create a custom look. The Bluetooth APP allows you to program the RGB diodes of any of our RGB, RGBW and RGBA strips with over 16 million different color combinations plus three pre-sets. Also, the Bluetooth APP offers 2 and 3 color rotation programming along with two timer features. Click the BLUETOOTH APP navigation tab on this product page for significantly more information on both the Bluetooth capabilities and APP functionality (including a video showing how the Bluetooth APP works)

RGBW: On the RGBW led strip, in addition to RGB, you get one extra diode which is Warm White. That warm white diode has a Kelvin temperature of 2400 which means it has a yellowish look giving it a warmer, softer, candle like look (see photo below). That fourth diode on the RGBW led strip can be wired directly to our GEN2 LED Controller which supports RGBx LEDs. As an option, you could also wire that fourth diode to a completely separate on/off switch. Your choice. You could also use the Quick-Switch feature with this fourth diode too.

RGBA: On the RGBA led strip, in addition to RGB, you get one extra diode which is AMBER. That fourth diode on the RGBA led strip can be wired directly to our GEN2 LED Controller which supports RGBx LEDs. As an option, you could also wire that fourth diode to a completely separate on/off switch. Your choice. You could also use the Quick-Switch feature with this fourth diode too.

WHAT IS RGB + AMBER (RGBA)?

RGBA is a LED strip format Boogey Lights® developed. It is available in both our Low Profile and Heavy Duty LED strip formats. The RGBA led strip includes our core RGB tri-chip technology using a 5050 RGB LED with the addition of a fourth 2835 diode that is AMBER. Designed primarily for motor vehicle applications, that fourth AMBER diode can be wired to a separate switch on the dash (or tied into a relay to work with existing running lights) that allows you to quickly and easily turn on just the AMBER leds. Then, for those who want the flexibility to be able to display up to 16 million color combinations using the RGB tri-chip, they can do that too. RGB + A provides the best of both worlds. Single color amber plus RGB tri-chip multi-color. The product photo carousel of this product page includes a close-up view of the LED strip design and wiring diagram. Note that due to the addition of that fourth diode, the RGBA strips are a little wider than our standard tri-chip RGB and single color LED strips. Also, the power lead wires use five conductor vs four. For additional information including product specs, click the SPECS navigation tab on this product page.

What is RGB + WHITE (RGBW)?

On the RGBW led strip, in addition to RGB, you get one extra diode which is Warm White. That warm white diode has a Kelvin temperature of 2400 which means it has a yellowish look giving it a warmer, softer, candle like look (see photo below). That fourth diode on the RGBW led strip can be wired directly to our GEN2 LED Controller which supports RGBx LEDs. As an option, you could also wire that fourth diode to a completely separate on/off switch. Your choice. You could also use the Quick-Switch feature with this fourth diode too.

WHAT IS DUAL COLOR?

The Dual Color LED configuration uses our RGBA LED strip but instead of pairing that LED strip with an RGB LED controller (to mix up to 16 million different color combinations), we hard wire a combination of one, two or all three of the RGB diodes (red, green or blue) along with the AMBER diode to two on/off switches. One switch operates the primary color diode(s). The other switch operates the amber diode. There are a total of seven Dual Color configuration options: RED+AMBER, GREEN+AMBER, BLUE+AMBER, MAGENTA+AMBER, YELLOW+AMBER, CYAN+AMBER, WHITE+AMBER. With a Dual Color configuration you don't need an LED Controller. Instead, you only need two switches (and relays); one to control each color. The primary color is chosen from the available dual color drop down list. The secondary color is always amber. Note: The Dual Color options includes one ON-OFF-ON 3 way toggle switch and two, 30 amp relays.

LED STRIP LENGTH LIMITATIIONS

The maximum length of a single LED strip is 16' (300 LEDs). They cannot be daisy chained together as you run a very real risk of fire and/or damaging the LED strips permanently. The laws of electricity won't allow it to go longer with today's commercially available technology using 12vdc power and super bright 5050 led chips. If your application requires longer than 16' (e.g. 20'), you have two options. One is to simply center the 16' LED strip in that 20' space. Boogey Lights are already very bright so for most folks, having enough light is never a concern. This is what most people do. That said, some prefer to have full coverage of the entire 20' area. In that case it's possible to cover that entire 20' span using two LED strips. In the case of a 20' span you can order two - 10' LED strips. Then, the two LED strips (totaling 20') are installed such that the two LED strips butt together; end to end, which gives the illusion of a single 20' long LED strip.

ALUMINUM CHANNEL OPTION

This product selection is optional but if you can afford it, we suggest adding it. Why? Because they provide a professional looking installation. Not only does the channel and diffuser protect the LED strip the opaque plastic diffuser gives off a nice glow lighting effect too. The Mini T12 Aluminum Channel is a low profile design that can be mounted just about anywhere. It has an anodized finish (electrostatic sprayed) which provides maximum protection against the elements. The aluminum channel acts as a heat sink too. They're ideal for harsh indoor or outdoor use to protect the LEDs. The channel can be mounted any number of ways including adhesive tape, rivets or screws. For boat trailer applications, we suggest using rivets. On outdoor installations we advise adding some lexel / silicone to the ends of the channel to seal it.

WHAT'S INCLUDED + OPTIONS

This kit includes the LOW PROFILE LED light strips in the quantity and lengths you select based on your layout. Single Color, Dual Color, RGB, RGBA and RGBW available.

If you selected a multi-color system, the kit will include an LED Controller. Either Single Zone Heavy Duty or Dual Zone Heavy Duty based on your selection. Both include a wireless RF hand held remote control and Bluetooth integration. Also included is our eXtended Long Range Antenna. See product page for details.

If you selected a SINGLE COLOR system the kit will include the switching mechanism or controller you selected (if any).

If you selected a DUAL COLOR system the kit will include the switching mechanism or controller you selected.

Optional: Aluminum channels with plastic diffusers to match the length of the LED strips you ordered.

Installation supplies include 3M Adhesion Primer, Feeder Cable based on number of LED strips ordered/chassis and controller selection plus battery connection cable with fuse holder.

NOTE: We do NOT include a trailer / tow vehicle wiring harness with this kit. Why? Because there are too many variations and configurations possible. Plus, you can purchase a 4 way flat, 5 way or even 7 way trailer male/female plug/harness at any auto parts store, big box store or online. They're inexpensive and plentiful.

One Year Original Owner Limited Warranty

DOT COMPLIANCE

The AMBER and RED single color LED strips are DOT COMPLAINT. They conform to applicable provisions of the Federal Motor Vehicle Safety Standard 108 requirements. Click the button below for more information on this issue.

OTHER ITEMS YOU MAY NEED

No two installation scenarios are the same. Not everyone shares the same installation quality goals. Some folks are OK with twisting wires together, others want to solder them. Some folks are OK with running wires where they may be seen or unprotected to save money/time, others want a tidy, clean install without any wires showing. Some folks are OK with mounting their LED strips to whatever surface they can find, others want to take the time necessary to build out appropriate mounting surfaces to provide the best lighting effect on their vehicle. The point is it's not possible to provide all the materials necessary for all installation scenarios and quality goals. Our light kits provide the essential components needed for a high-quality, functioning lighting system. Installation of our light kit to your specific vehicle may however require additional items to make it look and fit the way you want. This is particularly the case with electrical wiring and mounting of LED strips. Before proceeding with your installation we suggest you consider THESE OTHER ITEMS.

Installation Information

IMPORTANT. You must have an understanding of 12vdc power. An essential skill with installation of any Boogey Lights LED products is knowing how to correctly wire the product to a 12vdc circuit. This includes understanding the importance of having a properly sized fuse at the power source, polarity, how to properly seal an electrical connection, using properly sized wire gauge for the load, measuring voltage and measuring the additional amperage draw you're adding. If you are uncertain or unfamiliar with any of these concepts, we urge you to ask someone who has the knowledge to assist you. Electricity is unforgiving.

INSTALL DOCUMENTATION

All of our installation documentation for this product (and all others) is available to download directly from our website (Click to download BYOK BOAT TRAILER LANDING STRIP INSTALL DOCS). We encourage you to download this information and review before placing your order. That way you'll have a solid understanding of what is required (and no surprises). Here are some of the most important installation documents for this product. You will find ALL available documentation in our INSTALLATION RESOURCES SECTION.

BOAT TRAILER LAYOUT

Boogey Lights Boat Trailer Landing Strip Light Layout

Boat Trailer Landing Strip LED Light Kit